<pre id="j37bn"></pre>
      <track id="j37bn"></track>

      <address id="j37bn"></address>

      <thead id="j37bn"><sub id="j37bn"><ol id="j37bn"></ol></sub></thead>

        <progress id="j37bn"><form id="j37bn"></form></progress>

        歡迎您訪福州豐潤電氣有限公司官方網站
        banner
        美國柏勒夫Marsh

         

        Type 41

        Type 41

        產品詳細

        Type 41 Precision Air Regulator
        • Superior regulation characteristics
        • Rugged, corrosion-resistant construction
        • Excellent stability and repeatability
        • Self-relieving of excess down stream pressure
        • Low droop at high flow
        • Mounting options available
        Product Detail:
        The Type 41 regulators are designed for applications requiring high flow capacity, low droop, high accuracy, and fine adjustment sensitivity. The use of Bellofram’s rolling diaphragm provides greater sensitivity and improved accuracy. In addition, Type 41 regulators offer reduced over-all size and several mounting options, providing direct interchangeability with more expensive competitors’ units.

        Ruggedly designed and constructed, the Type 41 regulators have housings of precision-cast aluminum. They are pressure tested, and are chromate treated for internal corrosion resistance. Every regulator is finished with vinyl paint which resists scratching, weathering and other physical abuse.
        Careful design and quality materials throughout assure long, trouble-free operation in the most difficult industrial environments. A rubberized, soft-seat valve stem provides stability and “forgives” dirt and other foreign matter. An aspirator maintains downstream pressure and compensates for droop when high flow occurs. The gauge port is convenient for gauge installation and can also be used as an additional full flow outlet.
        The design of these regulators is especially well suited for panel applications due to ease of mounting (only one panel hole required), small size, adjustment sensitivity (32 threads per inch on the adjusting screw), and knob.

        Models
        The Type 41 comes in two versions, Type 41-1 and Type 41-2. These two regulators offer the same performance in two slightly different packages.
        Type 41-1: This unit comes standard with 1⁄4" NPT ports and a knob, and can be panel mounted using either the center nut or the threaded shoulder holes, spaced 1.5 in. (38.1 mm) center-to-center.
        Type 41-2 : This unit comes standard with 1⁄4" NPT ports, a knob and a bonnet vent port which can be tapped for a 1⁄4" NPT fitting if desired. It can be panel mounted using either the center nut or the threaded shoulder holes, spaced 1.25 in. (32.7 mm) center-to-center.

        Part Numbers:
         
        Part Number
        Port Size
        Set Point Range
        BAR
        psig
        T41-1
        960-113-000
        1/4 NPT
        0-0.14
        0-2
        960-114-000
        1/4 NPT
        0-0.69
        0-10
        960-170-000
        1/4 NPT
        0-2.1
        0-30
        960-171-000
        1/4 NPT
        0-4.1
        0-60
        960-172-000
        1/4 NPT
        0-6.9
        0-100
        T41-2
        960-115-000
        1/4 NPT
        0-0.14
        0-2
        960-116-000
        1/4 NPT
        0-0.69
        0-10
        960-181-000
        1/4 NPT
        0-2.1
        0-30
        960-182-000
        1/4 NPT
        0-4.1
        0-60
        960-183-000
        1/4 NPT
        0-6.9
        0-100
        Options:
        Option Ordering Matrix:
        Replace the last three digits of the part number with digits from the table below. If more than 2 combination needed, Consult Factory.
        OPTION
        1
        2
        5
        6
        7
        8
        1
        Fluorocarbon Pintle
        001
        021
        051
        061
        071
        081
        2
        Non-Relieving
         
        002
        052
        062
        072
        082
        5
        Epoxy Coating
         
        005
        065
        075
        085
        6
        Tapped Vent (T41.2 only)
         
        006
        076
        086
        7
        Mounting Bracket
         
        007
        087
        8
        Pressure Gauge
         
        008

        Fluorocarbon Pintle: A special elastomeric pintle used where elements in the supply air, such as flame retardant synthetic lubricants, are particularly destructive to ordinary pintle material.
        Non Relieving: Used in applications where it is desirable to relieve pressure downstream of the regulator, for some constant flow applications, and where the gas flowing through the regulator must not escape at the regulator. Non-relieving regulators should not be used for low or no flow applications.
        Corrosive Resistant Epoxy finish: An epoxy paint applied to the body and bonnet of the regulator exterior surfaces to provide increased corrosion resistance.
        Tapped Vent (T41.2 only): Allows installation of plumbing to capture exhaust air.
        Mounting Bracket: Steel (dichromate finish) bracket for side mounting. P/N: 607-000-057
        Pressure Gauge: Dual scale 2 in. (50.8 mm) gauges. Ranges include 0-30 psig (0-200 kPa), 0-60 psig (0-400 kPa), 0-100 psig (0-700 kPa) and 0-160 psig (0-1100 kPa). When specified with regulator, the correct range will be supplied. For NPT versions only.

         

        Cart:

         

         


        分享到:

         

         

        上一條:Type 40  

        下一條:Type 70

        點擊次數:點擊代碼  更新時間:2011-9-30 20:26:37  【打印此頁】  【關閉

         

         

         

        二維碼

         

        聯系我們 | 網站地圖 Copyright 2016 福州豐潤電氣有限公司 版權所有 | 網站備案/許可證號: 閩ICP備16038147號-1   網站建設信和網絡