<pre id="j37bn"></pre>
      <track id="j37bn"></track>

      <address id="j37bn"></address>

      <thead id="j37bn"><sub id="j37bn"><ol id="j37bn"></ol></sub></thead>

        <progress id="j37bn"><form id="j37bn"></form></progress>

        歡迎您訪福州豐潤電氣有限公司官方網站
        banner
        美國柏勒夫Marsh

         

        Type 40

        Type 40

        產品詳細

        Type 40 Regulator
        • Superior regulation characteristics
        • Rugged, corrosion resistant construction
        • Low cost
        • Excellent stability and repeatability
        • Self-relieving
        • Low droop at high flow
        • Several mounting options
        Product Detail:
        Marsh Bellofram’s General Purpose Type 40 Pressure Regulator is a reliable precision unit designed for instrumentation and general purpose use. Test data for the Type 40 regulator shows excellent performance characteristics compared with those of similar units presently on the market. The Type 40 regulator is generally superior in regulated pressure vs. flow, forward-to-reverse flow offset, supply pressure sensitivity, repeatability and stability.

        Ruggedly designed and constructed, the Type 40 has housings of diecast
        aluminum. Every regulator is finished with vinyl paint (which resists scratching, weathering and other physical abuse) and is pressure and leak tested prior to shipment from the factory. Careful design and quality materials throughout assure long, trouble-free operation in the most difficult industrial environments. A rubberized, soft-seat valve stem provides positive shut-off and “forgives” dirt or other foreign matter. An aspirator maintains downstream pressure and compensates for droop when high flow occurs. The gauge port is convenient for gauge installation and can also be used as an additional full flow outlet.

        The Type 40 regulator has a 60-mesh 304 stainless steel screen to block foreign particles from entering the output stream. The design of these regulators is especially well suited to pilot-operated controllers and instruments, as well as applications such as air chucks, air spray guns, air cylinders and actuators, and a wide range of industrial pneumatic systems and equipment.

         

        Part Numbers:
        Part Number
        Port Size
        Set Point Range
        BAR
        psig
        960-063-000
        1/4 NPT
        0-0.7
        0-10
        960-064-000
        1/4 NPT
        0-24
        0-35
        960-065-000
        1/4 NPT
        0-4.1
        0-60
        960-066-000
        1/4 NPT
        0-8.3
        0-120
        To order BSPT threads (including the gauge port) add “BSPT” to end of part number.
        Options:
        Option Ordering Matrix:
        Replace the last three digits of the part number with digits from the table below. If more than 2 combination needed, Consult Factory.
        OPTION
        1
        2
        3
        5
        6
        7
        8
        9
        10
        11
        1
        Fluorocarbon Pintle
        001 021 031 051 061 071 081 091 101 111
        2
        Non-Relieving
          002 032 052   072 082 092   112
        3
        Knob
          003 053 063 073 083   103 113
        5
        Epoxy Coating
          005 065 075 085 095 105 115
        6
        Tapped Vent
          006 076 086 096 106 116
        7
        Mounting Bracket
          007 087 097 107 117
        8
        Pressure Gauge
          008 098 108 118
        9
        Tamper-Resistant Cover
          009 109 119
        10
        Soft Relief Seat
          010 110
        11
        Florocarbon Diaphragm
          011

        Fluorocarbon Pintle: A special elastomeric pintle used where elements in the supply air, such as flame retardant synthetic lubricants, are particularly destructive to ordinary pintle material.
        Non Relieving: Used in applications where it is desirable to relieve pressure downstream of the regulator, for some constant flow applications, and where the gas flowing through the regulator must not escape at the regulator. Non-relieving regulators should not be used for low or no flow applications.
        Corrosive Resistant Epoxy finish: An epoxy paint applied to the body and bonnet of the regulator exterior surfaces to provide increased corrosion resistance.
        Mounting Bracket: Steel (dichromate finish) bracket for side mounting. P/N: 607-000-057
        Knob: Option to replace the square head pressure adjusting screw.
        Tapped Vent: Allows installation of plumbing to capture exhaust air.
        Pressure Gauge: Dual scale 2 in. (50.8 mm) gauges. Ranges include 0-30 psig (0-200 kPa), 0-60 psig (0-400 kPa), 0-100 psig (0-700 kPa) and 0-160 psig (0-1100 kPa). When specified with regulator, the correct range will be supplied. For NPT versions only.
        Tamper Resistant Cover: An aluminum tubular cover placed over a slotted head adjusting screw and screwed onto the bonnet of the regulator with a wrench. Prevents ordinary hand adjustments.
        Soft Relief Seat: Used in applications where it is desirable to reduce the standard bleed rate from 6 SCFH [0.17 m3hr] to less than 0.1 SCFH [0.003 m3hr].
        Fluorocarbon Diaphragm: Diaphragm as well as all seals are made of fluorocarbon elastomer to prevent deterioration from elements in the air supply, such as flame retardant synthetic lubricants normally destructive to standard Nitrile material.

        Cart:

         


        分享到:

         

         

        上一條:Type 110  

        下一條:Type 41

        點擊次數:點擊代碼  更新時間:2011-9-30 20:28:20  【打印此頁】  【關閉

         

         

         

        二維碼

         

        聯系我們 | 網站地圖 Copyright 2016 福州豐潤電氣有限公司 版權所有 | 網站備案/許可證號: 閩ICP備16038147號-1   網站建設信和網絡